Orders confirmed before 2pm leave Nairobi the same working day.Get a quote →

All guides

FTTH & Fibre Optics · 7 min read

How to Use a Fiber Fusion Splicer: Step-by-Step Fusion Splicing for FTTH

By the ECA Networks technical desk · Last updated 12 November 2026

Most bad splices are made before the arc ever fires: a dirty fibre, a poor cleave or a forgotten sleeve. This is the routine our technical desk walks FTTH crews through, from opening the cable to coiling the finished splice in the tray.

Short answer

Fusion splicing is four jobs done in order: strip and clean the fibre, cleave it flat, let the fiber fusion splicer align and arc the two ends together, then protect the joint with a heat-shrink sleeve. On good single-mode fibre a clean, calibrated splicing machine should estimate well under 0.1 dB of loss. Confirm the result with an OTDR before you close the enclosure.

This hardware is stocked under Fibre Optics Solutions on the ECA Networks online store, with live pricing and stock.

Shop Fibre Optics Solutions

What you need before you start

  • Fiber fusion splicer, charged, with clean V-grooves and electrodes
  • Precision cleaver
  • Jacket and coating strippers
  • Isopropyl alcohol (99% or better) and lint-free wipes
  • Heat-shrink splice protection sleeves
  • Splice tray or enclosure, and a container for fibre offcuts
  • OTDR or light source and power meter to test the finished splice

Step-by-step fusion splicing

  1. 1Run the splicer's arc calibration when you start the day or arrive at a new site, especially after moving between altitudes.
  2. 2Slide a heat-shrink sleeve onto one of the two fibres now. Forgetting it means breaking the finished splice and starting again.
  3. 3Strip the cable jacket and buffer to expose the 250 µm coated fibre, then strip the coating to bare glass over the length your cleaver and holder need.
  4. 4Clean the bare fibre with alcohol on a lint-free wipe, pulling in one direction. From here, do not let the clean glass touch anything.
  5. 5Cleave the fibre at the length marked for your splicer's holder. A precision cleaver gives a flat, square end face.
  6. 6Place the fibre in the splicer's holder or V-groove without touching the cleaved tip. Repeat steps 3 to 6 for the second fibre.
  7. 7Close the wind cover and start the splice. The machine images both ends, checks the cleave angle, aligns the fibres and fuses them with an electric arc.
  8. 8Read the estimated loss on the screen. If it is high, or the machine reports a cleave or alignment error, redo the splice rather than accept it.
  9. 9Open the cover gently, slide the sleeve over the joint so it sits centred, and place it in the heater.
  10. 10When the heat cycle ends, let the sleeve cool, then lay it in the splice tray and coil the spare fibre in generous loops.

Reading the fusion splicer's screen

The estimated loss is a calculation from the image, not a measurement, but it is a reliable early warning. These are the problems a splicer most often reports and what usually causes them:

What you seeUsual causeFix
Cleave angle errorWorn or dirty cleaver blade, or fibre not seated flatClean the cleaver, rotate the blade position, recleave
Bubble or dark spot in the jointDust or alcohol residue on the fibre endClean again, let alcohol evaporate, recleave
Splice looks thin or thickArc power wrong for the conditionsRun arc calibration and repeat
High estimated lossDirty V-grooves, poor cleave or mismatched fibre typesClean V-grooves, recleave, check both fibres are the same type
Fibre breaks when the cover opensGlass touched something after cleaningRestrip, clean and recleave

FTTH splicing: drops, pigtails and splitters

In an FTTH build, most fusion splicing happens in three places: feeder and distribution cables joined in closures, pigtails spliced onto cable fibres in ODFs and fibre access terminals, and drop cables joined at the customer end. Flat FTTH drop cable needs the right holder or careful preparation before it will sit in the splicer. Splice-on SC/APC connectors let you terminate a drop with a fusion splice and a factory-polished end face, which gives lower loss than a fast connector.

Keep a record of each splice by closure and tray. When a subscriber goes offline months later, that record is what lets a crew find the right fibre quickly.

Test every splice with an OTDR

The splicer's estimate is not proof. An OTDR shows the real loss at each splice and its distance along the cable. Test from both ends and average the two readings, because a single-direction OTDR reading can show a splice as a small gain or an exaggerated loss when two fibres differ slightly.

Safety and good habits

  • Put every glass offcut in a sealed container; fibre shards are hard to see and easy to push into skin
  • Wear eye protection and do not eat or drink at the splicing table
  • Clean the V-grooves and fibre clamps at the start of each day
  • Replace electrodes when the manufacturer's arc count is reached or splice quality drops

Frequently asked questions

What is a good splice loss for a fusion splice?+

On single-mode fibre a good fusion splice is typically well under 0.1 dB, and a well-maintained core-alignment splicer often estimates a few hundredths of a dB. Confirm the real value with an OTDR.

Why do I have to slide the sleeve on first?+

The heat-shrink sleeve has to go over the joint after splicing, and once the two fibres are joined there is no free end to slide it onto. Fit it before you cleave.

How often should I calibrate a fusion splicer?+

Run the arc calibration at the start of each working day, whenever you move to a site at a different altitude or temperature, and whenever splice quality drops.

Can I splice single-mode to multimode fibre?+

The splicer may join them, but the loss will be high in one direction and the link will not perform. Splice like with like.

Ready to spec the equipment?

Browse stocked hardware on the ECA Networks shop, or send us the spec for a quote.

Browse the shop

Related reading

FTTH & Fibre Optics

Choosing an ADSS span rating without guessing

Read guide

FTTH & Fibre Optics

Single mode or multimode for a campus backbone

Read guide

FTTH & Fibre Optics

Consumables that stall installations

Read guide

Need help with the specification?

Send the drawing, quantities or site notes. The technical desk will check the parts before you order.